What Can I Do With My Naza V2

Size and Weight

ESC Sound Introduction

Gear up	♪1234567
Throttle stick is not at bottom	BBBBBB…
Input bespeak abnormal	B——–B——–B…
Input voltage aberrant	BB—BB—BB—BB…

TX Parameters

Working Frequency	2.4GHz ISM
Command Channels	7 Channels
Advice Altitude	1000m
Receiver Sensitivity（ane%PER）	＞-100dBm
Ability Consumption of TX	＜20dBm
Working Current /Voltage	52 mA@6V
AA Battery	iv Required

Basic Parameters

Operating Temperature	-10°C ~ l°C
Ability Consumption	iii.12W
Take-off Weight	<1200g
Hovering Accuracy (GPS Mode)	Vertical: 0.8m Horizontal: 2.5m
Max Yaw Angular Velocity	200°/s
Max Tilt Angle	45°
Max Ascent / Descent Speed	6m/s
Max Flight Velocity	10m/s
Diagonal distance (motor center to motor center)	350mm
Phantom Prop Guard	Weight(Single):18.7g Size(Unmarried): Bending(155.0°) Radius(112.32mm) Whole Size with Iv Prop Guards: 575.5mm

Charger & Battery Parameters

Charger Air conditioning Input	100-240V
Charge Current	1A/2A/3A
Electric current Drain for Balancing	200mA
Power	20W
Battery Blazon	LiPo

Introducing the Phantom Self-tightening Propeller.

2013-09-12

Introducing how to install the Phantom upgrade kit.

2013-08-08

Introducing how to mount the Zenmuse H3-2D on your Phantom.

2013-07-03

Release Notes

Naza-M Release Notes

2014-05-13
Phantom Release Notes

2015-02-03
Phantom Upgrade Kit Release Notes

2013-08-06

Assistant Software & Driver

Naza-M Assistant Software v2.20 （Stop distributing and updating)

2013-10-25
@Naza-M Firmware* v4.02

2013-10-25
DJI WIN Driver Installer

2013-01-18
Phantom Default Configuration Parameters

2013-09-11
Naza-M Banana Software v2.20 （Terminate distributing and updating)

2014-05-13

Manuals

Phantom Prop Guard Assembly Didactics v1.02

2013-09-12
Phantom Flying Flowchart v1.0

2013-03-19
Phantom Quick Start Manual (EN) v1.7

2013-09-25
Phantom Advanced Manual (EN) v1.four

2013-03-22
Phantom Quick Start Transmission (FR) v1.vii

2014-02-18
Phantom Advanced Manual (FR) v1.four

2014-02-18
Phantom Quick Showtime Manual (DE) v1.7

2014-02-18
Phantom Advanced Manual (DE) v1.4

2014-02-18
Naza-M Quick Start Manual v1.26

2014-05-thirteen
Battery and Charger Pedagogy v1.0

2013-01-08
P330CB-H3-second Manual v1.00

2013-08-06
Phantom Slide Lever Manual v1.00

2013-08-06

* The above download list is only for Phantom.
We volition cease distributing and updating "Naza-One thousand Assistant Software v2.20 ( for WIndows & Mac)" on May 15, 2018, including adaptations to the new version of the operating arrangement. Later on May xv, 2018, the software is even so bachelor for download. The server shutdown time will be announced separately. Looking ahead, DJI volition continue to provide the best tools and services for users and developers.
* Important:
Use the Input function in the "Tools" of the Banana Software to input the "PHANTOM Default Configuration Parameters".
* Become to DJI Wiki for release history!

Basics

ane.Tin can I DIY any equipment on the top of Phantom?

No, you cannot install any other equipment or roofing on the top surface of Phantom, that will probably affect GPS point and functions.

2.Tin can I fly my Phantom with any WiFi part enabled equipment?

No, the WiFi betoken may interfere with the signal of the transmitter and bear upon your flight.

iii.Can I use thread locker when mounting the Phantom?

No, the thread locker may corrode the shell of Phantom, may cause fractures.

4.Tin can I utilise thread locker when mounting the propellers?

No, only tighten the screws is enough.

5.Where can I get the manual, assistant software and other materials of Phantom?

You tin can find all the related materials from DOWNLOADS at PHANTOM page on https://www.dji.com/sg/

six.Where can I find relevant videos of Phantom?

You can notice all the related videos on the PHANTOM web page at https://www.dji.com/sg/

7.Where can I get the data well-nigh "Software and Commuter Installation ", " Configuration and Firmware & Software Upgrade ", " Linking the Transmitter and Receiver " and " Changing the Control Mode of the Transmitter ", " Transmitter Calibration ", " Mounting the Camera and Camera Frame " and " Intelligent Orientation Control (IOC) Flight ", etc?

Delight download the Advanced Manual from the PHANTOM spider web page.

8.Where can I go the information nearly the bombardment and charger?

Please download the Battery and Charger Education from the PHANTOM spider web page.

9."Organization initializing and self-checking LED flashes" are not correct (Cerise LED appears in the concluding four light-green flashes).

The autopilot organisation works abnormally. Please contact your dealer.

10.Some risks may occur during the flight.

Please exist sure to read the instructions and get familiar with this production before flying, otherwise there could be a serious blow. Aircraft crashed, rotating propeller may hurt people and objects. Aircraft may be out of control or fifty-fifty lost.

xi.After the system beginning and self-checking has finished, if the LED blinks Cherry, Green and Yellow continually.

Sensor error is too big. Please connect the assistant software, enter the "Tools" – > IMU calibration, scout the "IMU calibration" videos, acquit out basic calibration or avant-garde scale.
Damage of the accelerometer. Please contact your dealer.
Sensor does not work. Please contact your dealer.

12.After power on and before the motors start-up, the LED blinks Dark-green 6 times quickly.

If the PHANTOM is moved, information technology is normal.
If the PHANTOM is stationary, IMU calibration is necessary. Please connect the assistant software, enter the "Tools" – > IMU scale, watch the "IMU calibration" videos, comport out basic calibration or advanced calibration.

13.The shipping does not take off or turns over when pushing the throttle stick.

The propeller assembly is non correct. Check that the rotation of the propellers and motors are matched.
Sensor mistake is besides big, the system will not piece of work. Please connect the banana software, enter the "Tools" – > IMU scale, watch the "IMU calibration" videos, carry out basic calibration or avant-garde scale.

14.LED blinks Yellow 6 times quickly after the Control mode LED blinks.

The built-in sensors demand some time to attain a stable state. Make sure not to wing the PHANTOM until the 6 rapid yellow flashes disappear.

15.Under low temperature conditions, if I have six xanthous lights appearing continuously for a long fourth dimension, what can I do?

You lot can cover the ventilation holes with some agglutinative record.

xvi.The LED blinks Red and Yellow alternately.

Compass error is too big.

At that place may be a ferromagnetic substance close to the Phantom. Lift the aircraft up near 1m from the ground, if there is no Cherry-red and Yellow flashing, then it volition not bear on the flying.
Otherwise, re-calibrate the compass.
If re-calibration does not work, please connect to the Assistant Software, select the "Tools" and follow the tips to carry out the required operation.
The compass module is lacking, replace it. Please contact your dealer.

17.The aircraft is drifting during flight.

Sensor error is too large, IMU calibration may be required; for the calibration operation, please lookout the "IMU scale" video (online).

18.The shipping is suddenly out of control during flying.

The compass has been magnetized or not calibrated. Delight watch the "resetting the compass" video, (online), referring to the video carry out demagnetization. Then Recalibrate the compass.

xix.The aircraft drops height suddenly during flying and the LED flashes RED apace continually.

Depression-voltage protection is triggered. Delight land the aircraft ASAP.

twenty.The LED blinks Yellow quickly continually.

The TX point is lost.

Check that the transmitter is switched on and works unremarkably.
Check that the receiver and the main controller are continued correctly.
Check that the receiver setting is correct in the assistant software.

21.Firmware upgrade is abnormal when using the NAZA-M banana software.

Delight contact your dealer.

22.Afterward power on and before the motors get-go, if the control fashion LED double blinks without moving any TX stick.

This indicates that you take moved at least one TX sticks during system start up and self-check. Reboot the autopilot system.

23.The aircraft does not receive any satellite signals.

Please check if at that place are buildings that could exist blocking the satellite signal. GPS needs an open area to piece of work.
Please check whether at that place are objects placed on the top of the PHANTOM, that could be blocking the signal to the satellite sensor.

24.How practice I make up one's mind that the GPS module is in working status?

Please check if in that location are buildings that could exist blocking the satellite bespeak. GPS needs an open area to work.
Put the TX switch "S1″ to the peak position, if in that location is a mode low-cal blinking such as green single wink (or double wink), it means that the GPS is working correctly.
Later power on, if yous accept seen the red low-cal flashing one, two or three times indicating the number of satellites locked, it means that the GPS works correctly.

25.Unable to connect to the assistant software.

The driver is not installed properly. Reinstall the driver.
The banana software and firmware versions do not match. Upgrade the software or firmware.
If the LED indicator does not light solid Dark-green, it is probably the wire that is damaged or a bad connexion, or the LED module is cleaved. If it is sure the LED is cleaved, please contact your dealer.

26.The transmitter alarms when switched on.

The throttle stick is non at the lowest position, pull the throttle stick to the lowest position.
The transmitter has a low battery, alter the batteries in the transmitter.

27.Flying time shortens.

The battery is not in a good condition.
The bombardment is not fully charged.
Load weight increased.
The battery might be very common cold (i.e. cold weather).

28.LED indicator does work correctly.

Damaged LED module. Delight supercede information technology for a new LED module.

29.When I push button the throttle stick the Phantom has no response, why?

In order to prevent faulty operation, you need to execute CSC. Delight check the user transmission for detailed instructions.

30.When I execute CSC, motors have no response, why?

Delight observe the LED flashing status.
Four yellow flashes means preheating, and after preheating it will be OK.
Four green flashes means sensor fault, please connect to the assistant software and calibrate the IMU.
Four red flashes means the sticks are not in centre position, delight connect the software and calibrate the transmitter.

31.The LED lights are flashing usually, merely when I execute CSC, motors however have no response?

Please cheque the ability supply connection.
Please check the transmitter stick commands and its channel mapping in the software, it has to exist consistent and brand full range sliding. And check the throttle and pitch channel mapping.

32.Why exercise the LEDs flash yellow & red continuously later power on?

It means the compass has been compromised, please calibrate the compass.

33.The LED flashes red, yellow & green continuously, the software indicates ERR 25 and the acceleration shows Mistake, the shipping cannot have off?

The internal sensor may intermission down because of collision. Please contact your local dealer for after-sales service.

34.It asked me for SN after I install the assistant software, where can I get the SN?

The SN is already input, no demand to input again. This is because yous did non connect the main controller or you did non install driver correctly.

35.After I assembled the Phantom, every time I try to take-off it flips away?

Please read the user manual advisedly, this may be caused by wrong installation. Please check:
1. the orientation of the main controller;
two. the rotate management of the motor and propeller;
3. the ESCs are in the correct port;
four. set the correct mixer type in the software;

36.Why is the yellow light still blinking when I switch to GPS mode?

The main controller failed to identify the GPS &compass module. Please check the connection.

37.Why can the IOC not be used?

The IOC is an advanced functionality, and is default OFF. Please connect the assistant software to enable it.

38.The battery cannot exist charged, why?

Please contact the local dealer for repair.

39.Can I use large chapters battery for my Phantom?

Our standard battery is 2200mah, 20c, 3S battery. You lot tin can install more according to your model. There is non excessive much space, please brand certain that you take adequate space for your batteries.

forty.Where can I purchase the accessories?

Delight contact your local dealer.

41.How tin I use H3-2D gimbal on the early version Phantom?

You need to use PMUV2 or the Phantom upgrade kit.

Software Questions

ane.When my Phantom takes-off in attitude mode it volition drift bated, why?

Please check the motors and ESCs. Information technology is possible that the NAZA sensor error is too big, please connect to the assistant software and calibrate the IMU.

two.Does the Assistant software support Mac?

No, currently it works on Win XP, Win7, Win8.

3.I followed the didactics to register, only I did not receive whatsoever activation electronic mail?

Please brand sure your email address is correct and check the spam post.
It is recommended to utilise Gmail, hotmail, etc for registration.

4.NAZA-Yard Assistant Software Error Lawmaking List

CFG-ERR

Configuration mistake, this may cause by firmware upgrade from the former version, or abnormal Tx calibration. Re-calibrate your transmitter, ability cycle your controller, and check all of the parameters.

VOL-LOW [4]

Voltage low

SN-ERR

Your S/Northward is non available, Please contact your dealer. (Place of buy)

VOL-Low[6]

Voltage low

IMU-ERR

IMU ERROR,Please contact dealer. (Identify of purchase)

X1-ERR

You've chose parameters tuning by X1/X2 channel with Tx Knob, just no signal detected on X1/X2 input channel, or Tx didn't powered on.

X2-ERR

You've chose parameters tuning by X1/X2 channel with Tx Knob, but no signal detected on X1/X2 input channel, or Tx didn't powered on.

PMU-ERR

Delight bank check the connection among bombardment, MC and PMU.

RX-ERR

Please make certain you are on the RC folio of the NAZA Assistant Software, select the right receiver blazon or bank check the receiver connexion, after that power cycle your controller to take effect.

COMPASS-ERR

Compass data is abnormal, please restart your Controller, if you nonetheless get this mistake, delight contact your dealer (Place of buy).

Mistake [25]

IMU initialization failure, may exist caused past crash. Delight contact dealer (Identify of purchase).

Mistake [26]

Delight perform Advanced Scale.

Error [27]

GPS not calibrated, or magnetic field interference. Delight calibrate GPS once more in good condition. Please contact your dealer for all technical support questions.

5.Why my Windows 7 OS cannot install the assistant software driver successfully?

Some of the users who use WINDOWS 7 operating system may not accept the usbser.sys file, please download this file and put it into C: \ WINDOWS \ system32 \ drivers, then reinstall the driver.
Download the usbser.sys file.

harperlationd71.blogspot.com

Source: https://www.dji.com/phantom